75 mm swivel castor with a non-marking grey tyre and top-plate fixing. A direct replacement for the castors on Scrubtec scrubber dryers, vacuums and cleaning trolleys that rolls quietly and leaves no marks on clean floors.
430 mm disc scrubbing brush with Medium polypropylene bristles and a quick-fit hub. It clips straight onto Scrubtec scrubber dryers and single-disc machines for daily scrubbing of hard floors, with an even bristle pattern that wears flat.
This old-type Scrubtec part (XPZ-800) is no longer made and has been replaced by a newer, improved part that fits the same machines. The replacement is shown on this page and can be ordered straight away for the same job.
Replacement drive belt XPZ-850 for the brush and traction drives of Scrubtec scrubber dryers and sweepers. Built to the original length and profile, so it sits correctly in the pulleys, tensions as designed and runs quietly from the first start.
H13 HEPA filter H-300 for Scrubtec dry and wet-and-dry vacuums. It captures at least 99.95% of fine particles, so dust, allergens and fine debris stay in the machine instead of going back into the room. A sealed gasket stops air bypassing the media.
430 mm pad driver with a push-in centre lock, for Scrubtec scrubber dryers and single-disc machines. It holds floor pads flat and centred for scrubbing, stripping and polishing, and swaps pads in seconds without tools, so one machine can scrub and polish.
Front and rear squeegee blade set in Gum rubber for 750 mm Scrubtec squeegee frames. Fresh blades pick up all the dirty water in one pass, leaving floors dry, streak-free and safe to walk on soon after cleaning. The rear blade can be turned to use all four edges.
Two-stage 24 V DC vacuum motor (VM-550) for battery scrubber dryers. A through-flow bypass design keeps the motor windings out of the wet air stream, so it gives strong water pick-up shift after shift and is a direct fit for the original motor.
Original-fit Vacuum motor filter (VM-210) for Scrubtec scrubber dryers. It keeps dirt, fibres and foam out of the parts that cost most to repair, and it can be rinsed and reused many times before it needs replacing. Made to the original size, so it seals properly in its seat.
100 mm swivel castor with a non-marking grey tyre and top-plate fixing. A direct replacement for the castors on Scrubtec scrubber dryers, vacuums and cleaning trolleys that rolls quietly and leaves no marks on clean floors.
430 mm disc scrubbing brush with Hard polypropylene bristles and a quick-fit hub. It clips straight onto Scrubtec scrubber dryers and single-disc machines for daily scrubbing of hard floors, with an even bristle pattern that wears flat.
Replacement drive belt XPZ-1000 for the brush and traction drives of Scrubtec scrubber dryers and sweepers. Built to the original length and profile, so it sits correctly in the pulleys, tensions as designed and runs quietly from the first start.
H13 HEPA filter H-400 for Scrubtec dry and wet-and-dry vacuums. It captures at least 99.95% of fine particles, so dust, allergens and fine debris stay in the machine instead of going back into the room. A sealed gasket stops air bypassing the media.
510 mm pad driver with a push-in centre lock, for Scrubtec scrubber dryers and single-disc machines. It holds floor pads flat and centred for scrubbing, stripping and polishing, and swaps pads in seconds without tools, so one machine can scrub and polish.
Original-fit Recovery tank filter (RT-330) for Scrubtec scrubber dryers. It keeps dirt, fibres and foam out of the parts that cost most to repair, and it can be rinsed and reused many times before it needs replacing. Made to the original size, so it seals properly in its seat.
Front and rear squeegee blade set in Polyurethane for 750 mm Scrubtec squeegee frames. Fresh blades pick up all the dirty water in one pass, leaving floors dry, streak-free and safe to walk on soon after cleaning. The rear blade can be turned to use all four edges.
This old-type Scrubtec part (VM-200) is no longer made and has been replaced by a newer, improved part that fits the same machines. The replacement is shown on this page and can be ordered straight away for the same job.
125 mm swivel castor with a non-marking grey tyre and top-plate fixing. A direct replacement for the castors on Scrubtec scrubber dryers, vacuums and cleaning trolleys that rolls quietly and leaves no marks on clean floors.
510 mm disc scrubbing brush with Medium polypropylene bristles and a quick-fit hub. It clips straight onto Scrubtec scrubber dryers and single-disc machines for daily scrubbing of hard floors, with an even bristle pattern that wears flat.
Replacement drive belt SPA-1250 for the brush and traction drives of Scrubtec scrubber dryers and sweepers. Built to the original length and profile, so it sits correctly in the pulleys, tensions as designed and runs quietly from the first start.
Original-fit Solution filter (SL-120) for Scrubtec scrubber dryers. It keeps dirt, fibres and foam out of the parts that cost most to repair, and it can be rinsed and reused many times before it needs replacing. Made to the original size, so it seals properly in its seat.
Front and rear squeegee blade set in Gum rubber for 850 mm Scrubtec squeegee frames. Fresh blades pick up all the dirty water in one pass, leaving floors dry, streak-free and safe to walk on soon after cleaning. The rear blade can be turned to use all four edges.
510 mm disc scrubbing brush with Hard polypropylene bristles and a quick-fit hub. It clips straight onto Scrubtec scrubber dryers and single-disc machines for daily scrubbing of hard floors, with an even bristle pattern that wears flat.
Replacement drive belt 6PJ-1200 for the brush and traction drives of Scrubtec scrubber dryers and sweepers. Built to the original length and profile, so it sits correctly in the pulleys, tensions as designed and runs quietly from the first start.