Manufacturer: Scrubtec

Vacuum motor 24 V, 550 W

Two-stage 24 V DC vacuum motor (VM-550) for battery scrubber dryers. A through-flow bypass design keeps the motor windings out of the wet air stream, so it gives strong water pick-up shift after shift and is a direct fit for the original motor.
SKU: ST-VM550
Back order, expected 28 Dec 2026
Availability: Out of stock
Price
$189.00

Description

Overview

The vacuum motor is what lifts dirty water from the squeegee into the recovery tank. When it weakens, the machine leaves water on the floor, the squeegee lines stay wet and floors take longer to dry. When it fails, the machine is off the road until it is replaced.

This 550 W two-stage motor is a direct replacement for the original on Scrubtec battery scrubber dryers. It fits the same mounting, gasket and wiring, so a technician can swap it in well under an hour.

How it works

Two fan stages in series build the high suction needed to lift water through the squeegee hose. The motor is a bypass type: the wet working air passes only through the fan section and leaves through a separate outlet, while the motor itself is cooled by its own clean air stream. This keeps moisture and detergent away from the brushes, commutator and bearings.

Never fit a dry vacuum motor in a scrubber dryer. Dry motors draw the working air through the windings and fail quickly with water mist.

Key figures

The motor runs from the machine's 24 V battery pack and draws about 23 A at full load. Sealed suction is around 1,850 mm water column, enough to clear water from textured floors and grout lines in a single pass.

  • Two-stage fan, bypass (through-flow) cooling
  • Rated for continuous duty
  • Replaceable carbon brushes
  • Pre-fitted outlet gasket and spade terminals

Fitting

Disconnect the batteries before you start. Remove the recovery tank or motor cover, unplug the motor leads and release the mounting clamp or screws. Clean the motor seat, fit the new motor with its gasket, reconnect the leads with the correct polarity and refit the cover.

Run the vacuum and check for air leaks around the gasket. A leak at the motor seat reduces suction as much as a worn motor does.

Making it last

Most vacuum motors fail early because water or foam gets into them. Keep the vacuum motor filter in place and clean, don't overfill the recovery tank, and use a defoamer when cleaning with high-foam chemicals. Empty and rinse the recovery tank after every shift, and leave the lid open so it dries.

The carbon brushes wear with use. Check them at the service interval and replace them before they are worn down to the limit mark, or the commutator will be damaged.

  • Fit a new vacuum motor filter with the motor
  • Use a defoamer with high-foam detergents
  • Check carbon brushes every 500 running hours

Ordering and support

The motor is packed in a moulded carton to protect the fan housing. Trade customers can order it on account, and our service team can confirm compatibility from the machine's model and serial number before you buy.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Type Vacuum motor
Part code VM-550
Voltage 24 V
Duty cycle S1 continuous
General
Brand Scrubtec
Product type Bypass vacuum motor, two-stage
Application Scrubtec 24 V battery scrubber dryers
Country of manufacture Italy
Warranty 12 months against manufacturing defects
Performance
Fan stages 2
Sealed suction (mm H₂O) 1,850
Maximum airflow (l/s) 32
Speed (rpm) 19,000
Cooling Bypass, separate cooling air
Carbon brush life (h) About 700
Operating temperature (°C) 0 to +40
Electrical
Rated power (W) 550
Current at full load (A) 23
Supply type DC, battery
Motor type Brushed DC, permanent magnet
Connection 2 × 6.3 mm spade terminals, red + / black −
Insulation class F
Dimensions and weight
Dimensions (L × W × H, mm) Ø 145 × 160
Net weight (kg) 3.2
Packed weight (kg) 3.8
Materials and construction
Fan housing Painted steel, two-stage
Compliance and safety
Standards Suits machines to EN 60335-2-72
RoHS compliant Yes
Packaging and ordering
Pack quantity 1 motor with gasket
Packaging Moulded carton
Barcode type EAN-13

Documents

FAQs

Will this motor fit my scrubber dryer?

It fits Scrubtec 24 V battery scrubber dryers that use the VM-550 motor. Check the part code on the old motor or in the machine's parts list, or send us the model and serial number and we will confirm it.

Can I use a dry vacuum motor instead?

No. A scrubber dryer needs a bypass motor, which keeps the wet working air out of the windings. A dry vacuum motor draws water mist through the motor and fails quickly.

My machine leaves water behind. Is it the motor?

Not always. Check the squeegee blades, the squeegee hose for blockages, the recovery tank lid seal and the vacuum motor filter first. If all of those are fine and suction is still weak, the motor is the likely cause.

How long should a vacuum motor last?

With a clean filter and no water or foam getting in, expect well over a thousand running hours, with a carbon brush change part way through. Motors that fail early almost always show signs of water damage.

Are the carbon brushes replaceable?

Yes. Check them at the machine's service interval, around every 500 running hours, and replace them before they reach the wear mark to protect the commutator.

Do I need a technician to fit it?

A competent person with basic hand tools can fit it, following the steps on this page with the batteries disconnected. Many fleet operators have it fitted at the next service visit.