Manufacturer: Scrubtec

Drive belt XPZ-850

Replacement drive belt XPZ-850 for the brush and traction drives of Scrubtec scrubber dryers and sweepers. Built to the original length and profile, so it sits correctly in the pulleys, tensions as designed and runs quietly from the first start.
SKU: ST-DBXPZ850
In stock
Availability: In stock
Price
$6.50

Fits these machines

Description

Overview

A worn drive belt is one of the most common reasons a scrubber dryer loses brush pressure, slows down or starts to squeal. The belt stretches, the edges glaze and it begins to slip under load, so the brush no longer turns at full speed and cleaning results drop long before the belt actually breaks.

This replacement belt is made to the same profile and effective length as the original part XPZ-850. It drops into the existing pulleys without packing, shims or changes to the tensioner, and gets the machine back to its rated brush speed.

Where it is used

The range covers the belts found on Scrubtec walk-behind and ride-on scrubber dryers and on the matching sweepers. Narrow cogged V-belts drive the brush decks, wrapped narrow V-belts are used on larger cylindrical brush and side-broom drives, and the ribbed poly-V belt drives the compact traction units.

  • Brush deck drives on disc scrubber dryers
  • Cylindrical brush and side-broom drives on sweepers
  • Traction and auxiliary drives on compact ride-on machines
  • Workshop stock for contract cleaning and facilities fleets

Design and construction

The V-belts use an oil- and heat-resistant chloroprene compound around a low-stretch polyester cord. The XPZ belts have a cogged, raw-edge flank that bends easily around small pulleys and runs cooler. The SPA belt has a fabric cover for long life on larger pulleys. The poly-V belt is made from EPDM with precision-ground ribs for smooth, quiet running.

All belts are antistatic, which matters on machines that work on dry, polished floors where static can build up and discharge through the frame.

Choosing the right belt

Match the part code printed on the old belt, or look it up in the parts list for your machine. If the print has worn off, measure the top width and the outside length with a tape around the back of the belt, then compare with the specifications on this page. An old XPZ-800 belt is replaced by the XPZ-850, which suits the revised pulley position on later machines.

Never fit a belt that is close but not exact. A belt that is too long slips; one that is too short overloads the motor bearings.

Fitting and care

Isolate the machine and disconnect the batteries before you open the brush deck or drive cover. Release the tensioner, remove the old belt and check the pulleys for wear, rust or a sharp groove edge. A worn pulley will destroy a new belt quickly.

Fit the new belt by hand, without levering it over the pulley flange, then set the tension so the belt deflects about 1.5 per cent of its span under firm thumb pressure. Recheck the tension after the first few hours of running, when the belt beds in.

  • Inspect belts every 250 running hours
  • Replace a belt that is cracked, frayed or glazed
  • Keep belts clear of oil, solvents and chemical spills
  • Replace matched belts on twin drives as a pair

Ordering and stock

Belts are supplied singly in a labelled bag with the part code and barcode, ready for a service van or stores bin. Trade accounts can add them to a saved list or reorder in seconds with quick order by part code, and fleet operators often keep one spare belt per machine model so a breakdown never stops a cleaning shift.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Type Drive belt
Part code XPZ-850
General
Brand Scrubtec
Product type Replacement drive belt
Application Brush, broom and traction drives on scrubber dryers and sweepers
Country of manufacture Poland
Warranty 6 months against manufacturing defects
Performance
Belt profile XPZ narrow V, cogged raw edge
Effective length (mm) 850
Minimum pulley diameter (mm) 56
Maximum belt speed (m/s) 40
Operating temperature (°C) -30 to +80
Inspection interval Every 250 running hours
Dimensions and weight
Top width (mm) 9.7
Belt height (mm) 8
Net weight (kg) 0.07
Packed weight (kg) 0.10
Materials and construction
Belt compound Chloroprene rubber (CR)
Tension member Low-stretch polyester cord
Oil resistance Resistant to light oil and grease splash
Compliance and safety
Antistatic Yes, to ISO 1813
Standards ISO 4184
RoHS compliant Yes
REACH compliant Yes
Packaging and ordering
Pack quantity 1 belt
Packaging Labelled polybag
Barcode type EAN-13
Shelf life 5 years in cool, dry, dark storage
Storage temperature (°C) +5 to +25

Documents

FAQs

How do I find the right belt if the code on my old one has worn off?

Check the parts list in your machine's manual, which gives the belt code for each drive. If you don't have it, measure the top width and the outside length of the old belt and compare them with the profile and length on this page. Our team can also help if you send the machine model and serial number.

My machine used the XPZ-800 belt. What do I order now?

The XPZ-800 has been replaced by the XPZ-850. Later machines use a revised pulley position, and the slightly longer belt fits both the old and new layouts once the tensioner is set.

How tight should the new belt be?

Set it so the belt deflects by about 1.5 per cent of the distance between the pulley centres under firm thumb pressure. Check it again after the first few hours, as a new belt beds in and loosens slightly.

How often should drive belts be changed?

There is no fixed interval; it depends on load and conditions. Inspect the belts every 250 running hours and replace any belt that is cracked, frayed, glazed or that keeps slipping after adjustment.

Can I fit a standard belt from a motor factor instead?

A general-purpose belt of the same profile and length will often fit, but it may not be antistatic or rated for the small pulleys used on scrubber dryers. This belt matches the original specification, so it lasts as long as the one fitted in the factory.

Can I keep spare belts on the shelf?

Yes. Stored in the bag, away from heat, sunlight and ozone sources such as electric motors, they keep for about five years. Hang or lay them flat; don't hang them from a nail, which kinks the cord.