Manufacturer: Scrubtec

Pad driver 430 mm

430 mm pad driver with a push-in centre lock, for Scrubtec scrubber dryers and single-disc machines. It holds floor pads flat and centred for scrubbing, stripping and polishing, and swaps pads in seconds without tools, so one machine can scrub and polish.
SKU: ST-PD430
In stock
Availability: In stock
Price
$72.00

Fits these machines

Description

Overview

A pad driver turns a scrubber dryer or single-disc machine into a pad machine. It carries a floor pad on a gripping face, so you can scrub, strip, spray-clean or polish with the pad that suits the job, and change between them in seconds.

Pads give a more even result than brushes on smooth floors, and a pad driver lets one machine do daily scrubbing, periodic stripping and polishing.

Where to use it

Use a pad driver on smooth hard floors: vinyl, linoleum, terrazzo, sealed concrete, stone and polished finishes. For rough, textured or grouted floors, a disc brush cleans better because the bristles reach into the surface.

  • Daily scrubbing with red or blue pads
  • Stripping old polish with brown or black pads
  • Spray-cleaning and buffing with white or beige pads
  • Maintaining polished stone and terrazzo

Design and construction

The body is moulded in glass-filled polypropylene, so it stays flat and doesn't flex under the weight of the brush deck. The face has short, stiff grip bristles that hold the pad without glue or hook tape, and that let solution pass through to the floor.

The centre lock is a spring-loaded plastic boss that pushes through the hole in the pad and clips it in place. It keeps the pad centred, so it doesn't wander off the driver at speed, and releases with a squeeze.

Because the driver is lighter than a brush, the machine's pad pressure setting may need adjusting. Start at the lowest setting and increase it only until the pad cleans evenly; too much pressure wears pads quickly and loads the brush motor.

Choosing the size

Match the driver to the deck of your machine. The 430 mm driver suits 17-inch machines and takes 17-inch (432 mm) pads. The 510 mm driver suits 20-inch machines and takes 20-inch (508 mm) pads. Both use the three-lug quick-fit hub, the same as the matching disc brushes, so you can switch between brush and pad driver on the same machine.

Use and care

Centre the pad on the face, push the centre lock through and check it clicks. Fit the driver like a brush. Turn or replace the pad as it wears; a pad that is worn through lets the driver face touch the floor and can mark it.

After each shift, remove the pad, rinse the driver and pad separately and leave the driver to dry face up. Check the grip bristles from time to time; when they are worn flat, pads will slip and the driver should be replaced.

  • Always put down solution before scrubbing
  • Remove pads after use to stop them sticking
  • Store the driver flat, face up

Ordering

Each driver is packed in its own carton with size and part code on the label. Trade accounts can save it to an order list together with disc brushes, squeegee blades and floor cleaner for each machine type.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Diameter (mm) 430
Type Pad driver
General
Brand Scrubtec
Product type Pad driver
Application Scrubber dryers and single-disc floor machines
Country of manufacture Italy
Warranty 12 months against manufacturing defects
Machine size 17 in / 430 mm deck
Pad size 17 in (432 mm)
Suitable floors Smooth hard floors: vinyl, terrazzo, stone, sealed concrete
Performance
Maximum speed (rpm) 350
Operating temperature (°C) +5 to +60
Dimensions and weight
Overall height (mm) 60
Centre hole for pad (mm) 90
Net weight (kg) 1.6
Packed weight (kg) 2.0
Materials and construction
Body material Glass-filled polypropylene
Pad grip Short polypropylene grip bristles
Centre lock Spring-loaded push-in boss
Hub type Three-lug quick-fit clutch plate
Compliance and safety
RoHS compliant Yes
REACH compliant Yes
Packaging and ordering
Pack quantity 1 pad driver
Packaging Labelled carton
Barcode type EAN-13
Storage temperature (°C) 0 to +40

Documents

FAQs

Which pads fit the pad driver?

The 430 mm driver takes standard 17-inch (432 mm) floor pads, and the 510 mm driver takes 20-inch (508 mm) pads. Any pad with a standard centre hole works with the centre lock.

Do I need a pad driver or a brush?

Use a pad driver on smooth floors such as vinyl, terrazzo and stone, and for stripping and polishing. Use a disc brush on rough, textured or grouted floors, where bristles reach into the surface better than a pad.

Will the pad driver fit my brush hub?

Yes, if your machine uses the three-lug quick-fit clutch plate of the same diameter as our disc brushes. Pad driver and brush are interchangeable on the same deck.

Why does the pad slip off the driver?

Usually the pad isn't centred, the centre lock isn't fully clicked in, or the grip bristles have worn flat. Refit the pad carefully; if it still slips with a new pad, the driver needs replacing.

Can the pad driver be used on a high-speed burnisher?

No. It is rated for scrubber dryers and single-disc machines up to 350 rpm. High-speed burnishers need a driver designed for their speed.

How should I clean the pad driver?

Take the pad off after each shift, rinse the driver with clean water and leave it face up to dry. Rinse or wash the pad separately; a dirty pad left on the driver can stick to it.