Manufacturer: Arcvane

Plasma cutter 60 A, 20 mm clean cut

A 60 air plasma cutter for single phase 230 V that cuts steel, stainless and aluminium up to 20 mm with a clean edge. The pilot arc starts without touching the plate, so painted, rusty and expanded metal cut easily, and the built-in regulator and filter protect the torch.
SKU: AV-PC60
In stock
Availability: In stock
Price
$1,890.00

Description

Overview

Plasma cutting uses compressed air and an electric arc to melt and blow through metal. Compared with an angle grinder or an oxy-fuel torch, it cuts faster, leaves a narrow kerf and puts very little heat into the surrounding metal, so thin sheet stays flat. It cuts any conductive metal, including stainless and aluminium, which oxy-fuel cannot.

This Arcvane cutter uses a pilot arc. The arc forms inside the torch before it reaches the work, so you do not need to touch the plate to start a cut, and it carries on across gaps in mesh, grating and perforated sheet.

Key features

  • Pilot arc, no high frequency
  • Built-in air regulator and filter
  • Drag cutting and CNC interface on the 100 A model
  • Spare tips and electrodes in the box

Applications

The 40 A and 60 A models suit workshops, vehicle and agricultural repair, ductwork and maintenance teams. The 100 A model is built for fabrication shops and demolition work, and it has a CNC interface for cutting tables.

  • Cutting sheet, plate, box section and pipe
  • Stainless and aluminium sheet without a grinder
  • Gouging out old welds and cutting off seized bolts
  • Expanded metal, grating and painted steel
  • Shapes from templates with a guide or roller kit

Air supply matters

Most plasma problems come from the air. It must be clean, dry and oil-free, at the pressure and flow given in the specifications. Water and oil in the air shorten tip and electrode life sharply and spoil the cut. The built-in regulator and filter catch the last traces, but fit a water separator at the compressor and drain the tank daily.

Choose a compressor that delivers more free air than the cutter uses, so it is not running flat out. A belt-drive or rotary screw compressor with a dryer is ideal for regular cutting.

Choosing the right model

Choose by the thickness you cut most, not the maximum you might cut once. The clean-cut figure is the thickness the machine cuts at a useful speed with a good edge; the severance figure is the most it will cut through slowly. This model gives a clean cut up to 20 mm.

The 40 A and 60 A models run on single phase. The 100 A model needs a three phase 400 V supply.

Use and care

Drag cutting with the shield resting on the plate is the easiest way to make straight cuts. Hold the torch upright, let the arc exit fully through the underside and keep a steady speed; too slow leaves heavy dross, too fast leaves an uncut bottom edge. Check the tip and electrode regularly and replace them as a pair when the tip bore wears oval or the electrode pit is deeper than about 1.5 mm.

Cutting produces fumes, sparks and intense light. Wear a shade 5 to 8 filter or helmet, gloves and flame-resistant clothing, and cut in a well-ventilated area.

Compliance and ordering

The cutter is built to IEC 60974-1, IEC 60974-7 and IEC 60974-10 and is CE and UKCA marked. Spare tips and electrodes are included. Trade customers can add a compressor, air hoses and safety gear to the same order and buy on account.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Output (A) 60
Supply single phase 230 V
Process Air plasma cutting
Clean cut (mm) 20
General
Brand Arcvane
Product type Air plasma cutter with pilot arc
Application Cutting steel, stainless and aluminium
Country of manufacture China
Warranty 2 years (torch consumables excluded)
Performance
Cutting current range (A) 20–60
Severance cut (mm) 25
Pierce capacity (mm) 10
Rated duty cycle 60% at 60 A
Air pressure (bar) 5.0–6.0
Air consumption (L/min) 140
Arc start Pilot arc, contact-free, no high frequency
Operating temperature (°C) -10 to +40
Cooling Fan, thermostat controlled
Electrical
Open-circuit voltage (V) 270
Maximum input current (A) 32
Plug fitted 32 A blue (BS EN 60309)
Minimum generator (kVA) 9
CNC interface No
Dimensions and weight
Net weight (kg) 14
Dimensions (L × W × H, mm) 480 × 200 × 380
Packed weight (kg) 17
Materials and construction
Case Powder-coated steel
Torch connector Quick-release central connector
Air inlet 1/4" BSP male
Compliance and safety
Standards IEC 60974-1, IEC 60974-7, IEC 60974-10
CE / UKCA marked Yes
RoHS compliant Yes
Protection rating IP23S
Packaging and ordering
Pack quantity 1
Torch supplied 60 A hand torch, 6 m
Supplied with Torch, earth clamp, air hose, 2 spare tips and electrodes
Barcode type EAN-13

FAQs

What size compressor do I need?

The compressor must deliver more free air than the air consumption in the specifications, at the stated pressure, with some margin. As a rough guide, the 40 A model needs a compressor of at least 3 hp and the 100 A model a belt-drive or rotary screw unit. Always fit a water separator.

Why are my tips wearing out quickly?

The usual causes are wet or oily air, low air pressure, touching the tip to the plate without a drag shield, and starting the arc too often in mid-air. Dry the air supply, check the pressure while cutting, and replace tip and electrode together.

Can it cut stainless and aluminium?

Yes. Plasma cuts any metal that conducts electricity. Aluminium cuts quickly but leaves a slightly rougher edge, and stainless gives a clean edge with very little heat discolouration.

Will the arc interfere with computers or CNC controls?

No high frequency is used to start the arc, so interference is much lower than with older HF plasma cutters. The 100 A model also has a CNC interface for connecting to a cutting table.

What eye protection do I need?

Use a filter of shade 5 to 8 depending on current, in goggles, a face shield or a welding helmet. An auto-darkening helmet set to shade 9 is fine for higher currents. Bystanders need protection too.

Are spare tips and electrodes available?

Yes, a starter set is in the box and replacement tips, electrodes and shields are sold in packs. Trade customers can save them to a quick order list so repeat orders take seconds.