Manufacturer: Rotalign

Shaft seal 20 × 40 × 7 mm

Nitrile rotary shaft seal for a 20 mm shaft, with a spring-loaded main lip and a dust lip. It keeps oil and grease in and dirt and water out of gearboxes, pumps, motors and wheel hubs, and fits any seal of the same size from another maker.
SKU: RA-SS20407
In stock
Availability: In stock
Price
$2.50

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $2.38
50–199 $2.25
200+ $2.12

Fits these machines

Description

Overview

A rotary shaft seal sits in a housing around a turning shaft and stops lubricant from leaking out and dirt from getting in. When it hardens or wears, oil weeps from gearboxes and pumps, and grit reaches the bearings behind it. Replacing the seal when you replace a bearing is cheap insurance.

These seals follow DIN 3760 form AS: a rubber-covered outside diameter, a main sealing lip held against the shaft by a garter spring, and a second dust lip on the outside.

Where to use it

The range covers small shaft sizes used on gearboxes, pumps, electric motors, wheel hubs and machine spindles, including brush and drive units on cleaning machines. The sizes pair with common 6000 and 6200 series bearings on the same shafts.

  • Gearbox input and output shafts
  • Pump and motor shafts
  • Wheel hubs and castors on machines
  • Brush motors and drive units

Design and construction

The lip and outer cover are nitrile rubber, which resists mineral oils, greases and water. A steel insert gives the seal its shape, and the rubber outer diameter seals in the housing and helps fitting, even in light alloy housings. The spring keeps the lip in contact with the shaft as it wears and as the temperature changes.

The dust lip keeps dirt and splashes away from the main lip. Pack a little grease between the two lips when fitting to protect the dust lip on start-up.

Choosing the size

Seals are sized as shaft diameter × housing bore × width, in millimetres. Measure the shaft where the lip runs, not a worn groove, and the housing bore. Fit a seal of the same width or check that the housing is deep enough for it.

If the shaft has a groove worn where the old seal ran, either set the new seal slightly deeper or shallower in the housing so the lip runs on fresh metal, or repair the shaft with a sleeve.

Fitting

Clean the housing and shaft and remove burrs from any keyways and shaft ends. Lubricate the lip and the outside diameter with the oil it will seal. Press the seal in square with a fitting tool or a socket that bears on the outer edge, with the spring side facing the oil. Never hammer it directly.

  • Spring side faces the fluid being sealed
  • Cover keyways and threads with tape when fitting
  • Never run the seal dry
  • Replace the seal whenever the bearing is replaced

Ordering

Seals are packed singly in a labelled bag. Order them with the matching bearings, and keep a few of the most common sizes in stores. Trade accounts can reorder by part code with quick order.

Store spare seals flat in their bags, away from sunlight and electric motors. Don't hang them on hooks or thread them on wire, as that distorts the lip.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Type Shaft seal
Bore (mm) 20
Outside diameter (mm) 40
Width (mm) 7
General
Brand Rotalign
Product type Rotary shaft seal, spring-loaded
Application Gearboxes, pumps, motors, hubs and machine spindles
Country of manufacture Czech Republic
Warranty 12 months against manufacturing defects
Seal design DIN 3760 form AS: main lip, dust lip, rubber OD
Performance
Maximum surface speed (m/s) 10
Maximum shaft speed (rpm) 9,500
Maximum pressure (bar) 0.5
Operating temperature (°C) -40 to +100
Suitable media Mineral oils, greases, water
Dimensions and weight
Net weight (kg) 0.009
Packed weight (kg) 0.011
Materials and construction
Lip and cover material Nitrile rubber (NBR), 70 Shore A
Insert Carbon steel
Spring Carbon steel garter spring
Shaft tolerance h11
Housing bore tolerance H8
Shaft surface finish Ra 0.2 to 0.8 µm, 45 HRC minimum
Compliance and safety
Standards DIN 3760, ISO 6194-1
RoHS compliant Yes
REACH compliant Yes
Packaging and ordering
Pack quantity 1 seal
Packaging Labelled polybag
Barcode type EAN-13
Shelf life 7 years, stored to ISO 2230
Storage temperature (°C) +5 to +25

FAQs

How do I read the seal size?

The three numbers are shaft diameter, housing bore and width in millimetres. For example, 20 × 40 × 7 fits a 20 mm shaft in a 40 mm housing bore and is 7 mm wide.

Which way round does the seal go?

The spring side, the open side of the lip, faces the oil or grease being sealed, usually towards the bearing. The closed face with the dust lip faces outwards.

Can I use this seal with pressure?

Only very low pressure, up to about 0.5 bar. Gearboxes and bearing housings that are vented are fine; pressurised hydraulic shafts need a pressure-rated seal.

Is nitrile suitable for my fluid?

Nitrile works well with mineral oils, most greases and water up to 100 °C. It is not suitable for brake fluid, strong solvents or high temperatures; ask us about other materials for those.

My old seal left a groove in the shaft. What should I do?

Set the new seal a millimetre or two deeper or shallower so its lip runs on undamaged metal, if the housing allows. Otherwise fit a shaft repair sleeve, as a seal running in a groove will leak.

Should I replace the seal when I change a bearing?

Yes. Removing the bearing usually damages the old seal, and a hardened seal won't protect the new bearing. Seals cost little compared with the time to strip the machine again.