Manufacturer: Edgecraft

Drill bit set, 19 pieces

A 19-piece set of fully ground HSS drill bits in 0.5 mm steps, packed in a metal case with a size-marked rack. It covers clearance and pilot holes in steel, aluminium, plastics and timber, and keeps every size in its place in the van or workshop.
SKU: EC-SET19
In stock
Availability: In stock
Price
$22.00

Description

Overview

The Edgecraft 19-piece drill bit set holds HSS jobber bits in half-millimetre steps from 1 mm or 1.5 mm upwards. Each bit sits in its own marked slot, so you can see straight away which size is missing.

It is the practical choice when you need many sizes occasionally, rather than a lot of one size. Workshops often keep one set per bench and buy the busy sizes in packs of 10.

What it is for

The bits suit general drilling in metals, plastics and wood with hand drills, cordless drill drivers and pillar drills.

  • Clearance holes for metric bolts and machine screws
  • Tapping holes, for example 6.8 mm for M8 or 8.5 mm for M10
  • Pilot holes for wood screws and self-tapping screws
  • Sheet metal, brackets and light sections
  • Maintenance and repair work across a site

Design and construction

All bits are ground from M2 high-speed steel with a 135° split point that starts without a centre punch on most surfaces. The dimensions follow DIN 338 jobber lengths.

The case is pressed steel with a positive catch and a hinged rack that tilts up for easy picking. Sizes are stamped on the rack and on the shank of each bit above 3 mm.

Which set to choose

The 13-piece set runs from 1.5 to 7.5 mm and covers most screw and small bolt work. The 19-piece set runs from 1 to 10 mm, which adds the M8 and M10 tapping and clearance sizes. The 25-piece set runs from 1 to 13 mm for heavier fabrication and bolting.

Replacement bits in the common sizes are available in packs of 10, so a set does not have to be replaced when one size wears out.

Speeds and materials

High-speed steel is forgiving, but heat is still its main enemy. As a rule, a 3 mm bit can run at about 2,600 rpm in mild steel, a 6 mm bit at about 1,300 rpm and a 10 mm bit at about 800 rpm. Halve these speeds for stainless steel and roughly double them for aluminium and plastics.

If the bit squeals, smokes or produces blue chips, it is running too fast or the feed is too light. A steady feed that produces curled chips is right. In thin sheet, clamp the work to a piece of scrap timber to stop it grabbing as the bit breaks through.

For timber, the bits work well at higher speeds. In hardwood, back the bit out now and then to clear the flutes. The 19-piece case also makes it easy to check which size you used last, so pilot and clearance holes stay consistent across a job.

Use and care

Run small bits fast and large bits slowly, and use cutting oil when drilling steel. Clamp the work and wear safety glasses. Wipe the bits and close the case after use so the rack stays tidy.

Trade customers can add sets to a saved list or reorder them with quick order alongside fixings and consumables.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Type Drill set
Pieces 19
General
Brand Edgecraft
Product type HSS drill bit set
Application Steel, cast iron, non-ferrous metals, plastics and timber
Country of manufacture Czech Republic
Warranty Against manufacturing defects
Performance
Size range (mm) 1 to 10
Size steps (mm) 0.5
Point angle 135° split point
Helix type Type N, right-hand cutting
Maximum material strength (N/mm²) 900
Dimensions and weight
Dimensions (L × W × H, mm) 160 × 85 × 20
Net weight (kg) 0.75
Packed weight (kg) 0.82
Materials and construction
Bit material HSS-G (M2 high-speed steel), fully ground
Bit finish Bright
Case material Pressed steel with tilting rack
Size marking On the rack, and on shanks above 3 mm
Compliance and safety
Standards DIN 338 (dimensions)
Recommended PPE Safety glasses
Packaging and ordering
Pack quantity 1 set
Barcode type EAN-13
Replacement bits Common sizes sold in packs of 10
Storage temperature (°C) 5 to 40, dry

FAQs

Which sizes are in each set?

All three sets go up in 0.5 mm steps. The 13-piece set covers 1.5 to 7.5 mm, the 19-piece set 1 to 10 mm and the 25-piece set 1 to 13 mm.

Does the largest set need a 13 mm chuck?

Yes, the 13 mm bit has a full-diameter shank, so your chuck must open to 13 mm. Most cordless drill drivers and pillar drills have a 13 mm chuck.

Can I buy a single replacement bit?

The common sizes are sold as packs of 10 HSS jobber bits from the same range, so they fit the case. Search for the size you need under drill bits.

Are these bits suitable for masonry?

No. HSS bits are for metal, plastics and wood. For brick, block and concrete use SDS-plus masonry bits in a hammer drill.

Which bit do I use for tapping an M8 thread?

Use the 6.8 mm bit for an M8 coarse thread, or 7 mm if the set does not include 6.8. For M10, use 8.5 mm. These sizes are in the 19 and 25-piece sets.

How should I store the set?

Keep it closed and dry. A light wipe with an oily cloth now and then stops the bits rusting if they are kept in a cold van.