Manufacturer: Galecore

Air impact wrench 3/4"

A 3/4" air impact wrench with a twin-hammer mechanism for wheel nuts, suspension work and heavy bolting. It gives high, smooth torque with less kickback, and three power settings with forward and reverse let you match the force to the job.
SKU: GC-IW34
In stock
Availability: In stock
Price
$349.00

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $331.55
50–199 $314.10
200+ $296.65

Description

Product overview

The Galecore 3/4" air impact wrench uses a twin-hammer mechanism: two hammers strike the anvil on each turn, which gives a smoother, more even blow than a single hammer. The result is high torque for stubborn fasteners, with less vibration and kickback in the hand.

A power regulator gives three settings in forward. Reverse always runs at full power, so seized nuts come off quickly, while lower forward settings help you avoid over-tightening.

The 3/4" square drive takes standard impact sockets, and the compact head reaches into wheel arches and engine bays. A hanger loop lets you hang it from a balancer on a busy bay.

Key features

  • Twin-hammer mechanism
  • Three power settings, forward and reverse
  • Needs 120 L/min at 6.2 bar

Where to use it

Pick the drive size to suit the fasteners you work on most.

  • 1/2 inch: car and van wheel nuts, suspension and engine bolts
  • 3/4 inch: truck, bus and plant wheel nuts, structural steel
  • Tyre bays and mobile tyre services
  • Agricultural and fleet workshops
  • Dismantling seized fasteners in maintenance work

Design and construction

The housing combines a hard-wearing aluminium front with a composite grip that stays warm in cold workshops. The exhaust is directed down through the handle, away from the work and the operator's face. The trigger is variable, so you can start nuts slowly.

The 1/2 inch model has a friction ring anvil for quick socket changes. The 3/4 inch model has a pin and O-ring anvil that holds heavy sockets securely.

Both models are balanced so the weight sits over the grip, which reduces wrist strain when you work at arm's length or overhead under a lifted vehicle.

Air supply and setup

Impact wrenches need a good volume of air at around 6.2 bar at the tool. A small compressor or a narrow hose will rob the tool of power, so check your supply before blaming the wrench.

  • Use at least a 10 mm bore hose, kept as short as practical
  • Fit a filter, regulator and lubricator, or oil the tool daily
  • Set 6.2 bar at the tool inlet while it is running
  • Use impact-rated sockets only

Use and care

Put a few drops of air tool oil in the inlet before each day's use, unless the line has a lubricator. Drain water from the air line regularly; water in the motor causes rust and loss of power. Grease the hammer mechanism through the grease port every few months.

Do not use an impact wrench for final tightening of wheel nuts. Run them down, then tighten to the vehicle maker's figure with a torque wrench.

If the wrench will not be used for a while, store it clean and dry with a few drops of oil in the inlet.

Ordering for workshops

Each wrench comes with an inlet fitting, a bottle of air tool oil and the manual. Workshops can add impact sockets, hoses and couplers to the same order with quick order, and tier prices apply on multiple tools.

Spare anvils, hammer kits and trigger valves are available, so a worn wrench can be rebuilt in the workshop rather than replaced.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Type Impact wrench
Drive 3/4"
General
Brand Galecore
Product type Pneumatic impact wrench
Application Wheel nuts, heavy bolting, maintenance
Country of manufacture Taiwan
Warranty 1 year
Performance
Maximum torque (Nm) 2,000
Working torque, forward (Nm) 270 to 1,400
Free speed (rpm) 5,200
Impact rate (blows/min) 950
Bolt capacity Up to M27
Working pressure (bar) 6.2
Noise level (dB(A)) 96
Vibration (m/s²) 9.2
Operating temperature (°C) -10 to 40
Dimensions and weight
Net weight (kg) 4.6
Dimensions (L × W × H, mm) 230 × 95 × 240
Materials and construction
Hammer mechanism Twin hammer
Anvil Pin and O-ring
Housing Aluminium front, composite handle
Air inlet 3/8" BSP
Recommended hose bore (mm) 13
Exhaust Through the handle
Compliance and safety
Standards ISO 11148-6
CE / UKCA marked Yes
Packaging and ordering
Pack quantity 1
In the box Inlet fitting, air tool oil, manual
Barcode type EAN-13

FAQs

Which drive size do I need?

A 1/2 inch wrench covers cars, vans and most workshop bolting. Choose 3/4 inch for trucks, buses, plant and large structural bolts.

Why does my wrench feel weak?

Low power is almost always an air supply problem: too small a compressor, a narrow or long hose, or a restrictive coupler. Check you have 6.2 bar at the tool while it is running, not just at the compressor.

Can I use normal chrome sockets?

No. Chrome sockets are not designed for impact loads and can crack. Always use impact-rated sockets, which are usually black.

Can I tighten wheel nuts with it?

Use it to run nuts down only, on a low setting. Then tighten to the correct torque with a torque wrench, as an impact wrench cannot set an exact torque.

How do I look after it?

Oil the inlet daily or use a lubricator in the line, and drain water from your compressor and air line. Grease the hammer mechanism every few months.

What hose and coupler should I use?

Use at least a 10 mm bore hose for the 1/2 inch model and a 13 mm hose for the 3/4 inch model, with high-flow couplers. Keep the hose as short as practical.