Manufacturer: Galecore

Air framing nailer 50–90 mm

A clipped-head framing nailer for 50 to 90 mm nails, built for wall frames, roof trusses, decking and fencing. Switch between sequential and bump firing, set the depth without tools, and hang it on a joist with the rafter hook between shots.
SKU: GC-FN90
In stock
Availability: In stock
Price
$289.00

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $274.55
50–199 $260.10
200+ $245.65

Description

Product overview

The Galecore framing nailer drives 34 degree clipped-head nails from 50 to 90 mm into softwood framing, sheet bracing and structural timber. A light magnesium body and a balanced grip make it comfortable to use all day, overhead or at bench height.

Clipped-head nails sit close together in the strip, so the magazine holds more nails than a round-head nailer of the same length. That means fewer reloads on a busy frame.

The magazine loads from the rear and takes a full strip in one go. A window on the side shows how many nails are left, so you are not caught short halfway along a top plate.

Key features

  • Sequential or bump firing
  • Tool-free depth adjustment
  • Rafter hook and no-mar tip

Where to use it

It is the main tool for structural carpentry in timber.

  • Stud walls and wall frames
  • Roof trusses, rafters and noggins
  • Floor joists and bracing
  • Decking frames and fencing
  • Pallets, crates and site hoarding

Design and construction

The firing mode switch lets you choose sequential firing for accurate placement, or bump firing for speed on sheathing and long runs. A dry-fire lockout stops the tool firing when the magazine is nearly empty, which protects the driver blade and the timber.

The depth wheel at the nose sets how deep the head sits, without tools. A no-mar tip protects visible timber, and the 360 degree exhaust can be turned away from your face. The rafter hook folds away when not needed.

The trigger is a replaceable cartridge, so replacing a worn trigger takes a minute. The grip is wrapped in rubber for control with or without gloves.

Nails and air supply

Use 34 degree paper-collated clipped-head nails, bright or galvanised, from 50 to 90 mm long and 2.8 to 3.3 mm in diameter. Galvanised or stainless nails are needed for treated timber and outdoor work.

Buy nails by the box; trade account holders can keep a saved list so the right nails are reordered in a few clicks.

  • Working pressure: 5 to 8 bar
  • Hose: 8 mm bore is fine for one nailer
  • Even a small portable compressor will run it
  • Check local building rules for nail size in structural work

Safety and care

Always wear safety glasses and ear protection, and disconnect the air before clearing a jam, loading or adjusting the tool. Use sequential mode when working on ladders or near other people. Never carry the nailer with your finger on the trigger.

Put a few drops of air tool oil in the inlet at the start of each day. Keep the magazine clean, and replace the driver blade and bumper when nails start to stand proud.

If the nailer jams, disconnect the air, open the latch at the nose and remove the bent nail with pliers.

Packaging and ordering

The nailer comes in a carry case with safety glasses, oil and hex keys. Add nails, a hose and a compressor to the same order, or use quick order to restock nails by the box.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Type Framing nailer
Drive 34° clipped head
General
Brand Galecore
Product type Pneumatic framing nailer
Application Framing, trusses, decking, fencing
Country of manufacture Taiwan
Warranty 1 year
Performance
Nail length (mm) 50 to 90
Nail diameter (mm) 2.8 to 3.3
Nail collation Paper tape
Magazine capacity Up to 70 nails
Firing mode Sequential or bump, selectable
Depth adjustment Tool-free wheel
Working pressure (bar) 5 to 8
Noise level (dB(A)) 95
Vibration (m/s²) 4.5
Operating temperature (°C) -10 to 40
Dimensions and weight
Net weight (kg) 3.6
Dimensions (L × W × H, mm) 490 × 130 × 360
Materials and construction
Housing Magnesium body, rubber grip
Air inlet 1/4" BSP
Recommended hose bore (mm) 8
Exhaust 360° adjustable
Compliance and safety
Dry-fire lockout Yes
Standards ISO 11148-13
CE / UKCA marked Yes
Packaging and ordering
Pack quantity 1
In the box Carry case, safety glasses, oil, hex keys
Barcode type EAN-13

Documents

FAQs

Which nails does it take?

It takes 34 degree paper-collated clipped-head nails from 50 to 90 mm long. Round-head nails and plastic-collated strips will not feed correctly.

What size compressor do I need?

A framing nailer uses little air per shot, so a small 24 litre compressor will run one nailer at a normal pace. For two nailers or fast bump firing, use a larger tank or a site compressor.

When should I use sequential mode?

Use sequential mode whenever accuracy or safety matters, such as on ladders, near other people or when placing nails in exact spots. Bump mode is for fast, repetitive nailing on sheathing and long runs.

Why are the nails not going in fully?

First turn the depth wheel deeper, then check the pressure at the tool. If the problem continues, the driver blade or bumper may be worn and should be replaced.

Can I use it on treated timber?

Yes, but use galvanised or stainless steel nails, as bright nails corrode in treated timber and outdoors. Hardwoods may need a higher pressure setting.

Is the nailer delivered with nails?

No, nails are sold separately so you can choose the length and finish. Add them to the same order and use quick order to restock.