Manufacturer: Forgeline

Self-tapping screw pan head 4.2 × 13

Forgeline 4.2 × 13 mm pan head self-tapping screw that forms its own thread in a pre-drilled hole in sheet metal. Case hardened and zinc plated, it fixes ductwork, panels, trunking and enclosures firmly without nuts. Takes a PZ2 bit and comes in packs of 200.
SKU: FL-ST4213
In stock
Availability: In stock
Price
$0.50

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $0.48
50–199 $0.45
200+ $0.42

Sold in screws. Quantities round up to full packs.

Description

Overview

Self-tapping screws join thin metal parts without a nut or a tapped hole. You drill a pilot hole, then the hardened thread rolls its own mating thread in the sheet as the screw is driven. The result is a firm, vibration-resistant joint that can be undone and refitted.

These Forgeline screws have a low pan head with a wide bearing face and a pozidriv recess. They are made from case-hardened carbon steel and zinc plated for indoor use. The finish gives a neat, even look on visible panels and stops the screws rusting in the box.

Sold in packs of 200 screws.

Where to use it

Typical uses for pan head self-tappers include:

  • Ductwork, flashing and sheet metal fabrication
  • Electrical enclosures, trunking and cable tray lids
  • Machine panels, guards and covers
  • Vehicle body repairs and van racking
  • Fixing plastic parts and clips to steel

Design and construction

The thread is a coarse spaced pattern to ISO 1478 with a tapered point (form C), which lines up with the pilot hole and starts cutting straight away. The surface is hardened so the thread stays sharp in mild steel and aluminium, while the core stays tough enough not to snap.

The pan head sits proud of the surface with a flat underside that clamps the sheet evenly. It is a good choice where a countersunk head would pull through thin material. It also leaves enough head height to grip with pliers if a recess is ever damaged.

Choosing the right size

The first number is the thread diameter in millimetres and the second is the length under the head. Use 4.2 mm screws for lighter sheet up to about 2 mm, and 4.8 mm screws for thicker sheet or where you need more holding power.

Pick a length that passes right through all the layers with at least three threads showing on the far side. The recommended pilot hole and sheet thickness for each diameter are in the specifications.

Fitting tips

Drill a clean pilot hole and remove burrs, then drive the screw square to the sheet with a PZ2 bit. Use a low clutch setting on the driver. Overtightening strips the formed thread in thin sheet and the screw will spin.

For sheet without a pilot hole, use self-drilling (tek) screws instead. Outdoors or on roofing, choose screws with a sealing washer and an exterior coating.

When joining two sheets, clamp them together while you drill so the holes line up and swarf does not get trapped between the layers. Clean away swarf after fixing, because steel filings left on painted or stainless surfaces soon rust and stain.

Packaging and ordering

Screws are boxed in 200s with a size and barcode label. Electrical and HVAC contractors often keep two sizes on each van, so the most common panel and trunking jobs are covered without a trip back to the stores; trade customers can reorder in one go from their order history or with quick order.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Size 4.2 × 13
Finish Zinc plated
Type Pan head
Material Case-hardened carbon steel
Drive Pozidriv PZ2
General
Brand Forgeline
Product type Self-tapping screw, pan head
Application Thin sheet metal and plastic, indoors
Country of manufacture Taiwan
Warranty 12 months against manufacturing defects
Performance
Pilot hole in steel (mm) 3.2 to 3.5
Recommended sheet thickness (mm) 0.8 to 2.0
Operating temperature (°C) -40 to +150
Dimensions and weight
Thread pitch (mm) 1.4
Head diameter (mm) 8.0
Head height (mm) 3.1
Weight per 100 pieces (kg) 0.16
Packed weight (kg) 0.35
Materials and construction
Surface hardness (HV) 450 minimum
Thread type Spaced thread, ISO 1478
Point Form C, tapered
Coating thickness (µm) 5 to 8
Compliance and safety
Standards ISO 7049, ISO 2702
CE / UKCA marked Not required for this product
RoHS compliant Yes
Packaging and ordering
Pack quantity 200 screws
Packaging type Cardboard box with size label
Barcode type EAN-13 on pack label

Documents

FAQs

Do I need to drill a hole first?

Yes. These are self-tapping, not self-drilling, screws. Drill a pilot hole of the size given in the specifications, then drive the screw to form the thread.

What does 4.2 × 13 mean?

The thread diameter is 4.2 mm and the length under the head is 13 mm. Choose a length that passes through all the layers with at least three threads showing.

Can I use them in aluminium?

Yes, they work well in aluminium sheet and profiles. Use the larger end of the pilot hole range so the thread does not bind, and avoid overtightening.

Why does the screw keep spinning?

The formed thread has stripped, usually from overtightening or a pilot hole that is too big. Lower the clutch setting, or move up to the 4.8 mm size in a fresh hole.

Are they suitable for roofing sheets?

Not on their own. Roofing and cladding need screws with a sealing washer and an exterior coating to keep water out and resist corrosion.

Which bit do I need?

A PZ2 pozidriv bit fits both sizes. Using the correct bit reduces cam-out and protects the zinc finish on the head.