Manufacturer: Aquaforce

High-pressure hose 10 m

Steel-braided high-pressure hose for pressure washers, rated 250 bar and hot water up to 155 °C. A single wire braid and a tough rubber cover resist kinking, abrasion and being dragged across yards, with M22 swivel ends for quick, twist-free connection.
SKU: AF-HH10
In stock
Availability: In stock
Price
$39.00

Fits these machines

Description

Overview

The hose takes more abuse than any other part of a pressure washer. It is dragged over concrete, run over by vehicles, kinked around corners and left out in the frost. A damaged hose is also a safety risk, as a burst at 250 bar can cause serious injury.

This replacement hose has a steel wire braid under a thick rubber cover, so it holds full working pressure with a large safety margin and stands up to daily site use.

Where to use it

The hose suits cold-water and hot-water pressure washers up to 250 bar, from compact trolley units to larger site machines. Choose the 10 m hose for washing bays and vehicles, 15 m for general site work and 20 m when you need to reach round buildings or plant without moving the machine.

  • Vehicle and plant washing
  • Yard, car park and forecourt cleaning
  • Building and facade cleaning
  • Food and agricultural premises with hot water

Design and construction

The inner tube is oil-resistant synthetic rubber with an 8 mm bore, which keeps pressure loss low over long lengths. A single high-tensile steel wire braid carries the pressure, and the black rubber cover protects it from abrasion, oil and the weather.

Both ends have crimped M22 × 1.5 female swivel couplings with O-ring seals. The swivel lets the hose turn freely, so it doesn't twist and kink as you work.

Fitting and use

Check the threads and O-rings on the machine outlet and gun inlet, then screw the hose on hand-tight. The O-ring makes the seal, so there is no need for a spanner or thread tape. Run water through before you start the pump to purge air.

Lay the hose out without loops or tight bends, keep it away from hot exhausts and sharp edges, and don't let vehicles drive over it.

  • Never pull the machine along by the hose
  • Release the pressure before disconnecting
  • Drain and coil the hose loosely after use
  • Protect it from frost when stored

Inspection and replacement

Check the hose before each use. Replace it straight away if the cover is cut through to the braid, if the hose bulges, or if a coupling leaks or has moved on the hose. Never repair a high-pressure hose with tape or clamps. Our replacement hoses come fully assembled and pressure tested.

Ordering

Each hose is supplied coiled and bagged with a label showing its length and pressure rating. Trade accounts can order hoses, nozzles and guns together, and hire companies often keep spares of each length on the shelf.

If you run several machines, check that they all use M22 connections before standardising on one hose. A single hose type across a fleet means fewer spares, and any hose can go on any machine.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Length (m) 10
Type High-pressure hose
Outside diameter (mm) 15
General
Brand Aquaforce
Product type High-pressure washer hose
Application Cold- and hot-water pressure washers up to 250 bar
Country of manufacture Italy
Warranty 12 months against manufacturing defects
Performance
Working pressure (bar) 250
Burst pressure (bar) 1,000
Maximum water temperature (°C) 155
Maximum flow (l/min) 30
Operating temperature (°C) -20 to +155
Minimum bend radius (mm) 115
Dimensions and weight
Inside diameter (mm) 8 (DN8)
Net weight (kg) 2.4
Packed weight (kg) 2.6
Materials and construction
Inner tube Oil-resistant synthetic rubber
Reinforcement 1 high-tensile steel wire braid
Cover Black abrasion-resistant rubber
Connections M22 × 1.5 female swivel, both ends
Coupling material Zinc-plated steel, crimped
Compliance and safety
Standards EN 853 1SN construction
Pressure tested Yes, every assembly
RoHS compliant Yes
Packaging and ordering
Pack quantity 1 hose
Packaging Coiled and bagged, labelled
Barcode type EAN-13
Storage temperature (°C) 0 to +30

Documents

FAQs

Will this hose fit my pressure washer?

It fits machines and guns with M22 × 1.5 male threads, which most professional pressure washers use. If your machine has a quick-release or proprietary fitting, check with us before ordering, as an adaptor may be needed.

Can I use it with a hot-water pressure washer?

Yes. The hose is rated for water up to 155 °C at 250 bar. Keep it away from the burner exhaust and other hot surfaces.

Which length should I choose?

Use the shortest hose that reaches the work, as every metre adds a little pressure loss and weight. The 10 m hose suits wash bays, 15 m general site work and 20 m reaching round buildings and plant.

Can I join two hoses together?

Yes, with a rated M22 male-to-male joiner, but expect some pressure drop over long runs. Never join hoses with clamps or repair a damaged hose; replace it.

Do I need thread tape on the fittings?

No. The seal is made by the O-ring in the coupling, so screw it on hand-tight. If it leaks, replace the O-ring rather than overtightening.

When should a hose be replaced?

Replace it at once if the braid is showing, the hose bulges, or a coupling leaks or has moved. Check the whole length before every use.