Manufacturer: Spatterline

Gas regulator with flowmeter, CO2

A single-stage gas regulator for CO2 with a 0–30 L/min flow gauge and a 5/8" UNF outlet. The clear flowmeter lets you set exactly the gas a weld needs, which saves gas and prevents porosity, and the brass body is made for daily workshop use.
SKU: SP-RGCO2
In stock
Availability: In stock
Price
$99.00

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $94.05
50–199 $89.10
200+ $84.15

Description

Overview

A welding regulator does two jobs. It reduces the high pressure in the cylinder to a safe working pressure, and it lets you set the flow of shielding gas to the torch. This Spatterline regulator does both in one compact brass body, with a contents gauge for the cylinder and a flow gauge calibrated in litres per minute.

Setting the right flow matters more than many welders think. Too little gas lets air reach the weld and causes porosity; too much wastes gas and creates turbulence that draws air in. A calibrated flowmeter takes the guesswork out.

Key features

  • 0–30 L/min flowmeter
  • Brass body, 5/8" UNF outlet
  • Hose tail and clamps included

Which regulator for which gas

Choose the version that matches the cylinder you use. The cylinder connections are different for inert gases and for CO2, so the two versions are not interchangeable.

  • Argon and argon mix: MIG welding of steel with argon and CO2 mixes, MIG on aluminium and all TIG welding
  • CO2: MIG welding of steel with pure CO2 and flux-cored wire that needs gas
  • Both: 5/8" UNF outlet to suit standard welder gas hoses
  • Both: built-in relief valve for safety

Setting the flow

As a starting point, set 6 to 10 L/min for TIG, 12 to 16 L/min for MIG on steel indoors and 15 to 20 L/min for MIG on aluminium or in a draught. Set the flow with gas running through the torch, not with the trigger released, and check it again after changing the torch or nozzle.

Pure CO2 cools as it expands. At high flow rates or in continuous use, a CO2 regulator can freeze. If you weld with CO2 at more than about 15 L/min for long periods, fit a CO2 heater ahead of the regulator.

Installation and safety

Secure the cylinder upright with a chain or strap before fitting the regulator. Crack the cylinder valve briefly to blow dust from the outlet, then fit the regulator by hand and tighten with a spanner without excessive force. Never use oil, grease or PTFE tape on cylinder connections. Open the cylinder valve slowly while standing to one side of the gauges.

Check joints for leaks with a leak detection spray after fitting and whenever you change cylinders. Close the cylinder valve at the end of each working day.

Care and replacement

Keep the regulator clean and protect the gauges from knocks; a damaged gauge glass or a bent needle is a reason to replace the unit. If the outlet pressure creeps up when the torch is not in use, or the regulator hisses, take it out of service and replace it. A regulator in daily use should be checked by a competent person at least every year and replaced at the interval the gas supplier recommends.

Compliance and ordering

The regulator is made to ISO 2503 and is CE and UKCA marked. It comes with a hose tail and clamps ready to connect. Trade customers can add one to a welder order, keep spares on a quick order list and buy on account.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Type Regulator
Gas CO2
General
Brand Spatterline
Product type Single-stage regulator with flowmeter
Application MIG welding with CO2
Country of manufacture Italy
Warranty 2 years
Performance
Flow range (L/min) 0–30
Maximum inlet pressure (bar) 230
Contents gauge range (bar) 0–250
Flowmeter type Gauge flowmeter with calibrated orifice
Recommended flow (L/min) 12–18
Operating temperature (°C) -20 to +60
Dimensions and weight
Net weight (kg) 1.0
Dimensions (L × W × H, mm) 170 × 110 × 75
Packed weight (kg) 1.2
Materials and construction
Body Forged brass
Diaphragm Stainless steel
Gauge diameter (mm) 50
Cylinder connection Type 30 (AS 2473)
Outlet connection 5/8" UNF male
Hose tail bore (mm) 6
Compliance and safety
Standards ISO 2503
CE / UKCA marked Yes
Relief valve Yes, built in
Heater needed For flows above 15 L/min in continuous use
Packaging and ordering
Pack quantity 1
Supplied with Hose tail, two hose clamps and sealing washer
Barcode type EAN-13

FAQs

Can I use the argon regulator on a CO2 cylinder?

No. Inert gas and CO2 cylinders have different valve connections so the wrong regulator cannot be fitted. CO2 also needs a regulator built to cope with its cooling effect. Buy the version that matches your gas.

Will it fit my welder?

The outlet is 5/8" UNF, and a hose tail is supplied for a standard 6 mm gas hose. That suits most MIG and TIG welders, including all Arcvane models. If your welder has a push-fit gas inlet, use a short length of hose and the clamps supplied.

What flow rate should I set?

Start at 6 to 10 L/min for TIG and 12 to 16 L/min for MIG on steel indoors. Increase it for aluminium, large nozzles or draughty conditions. More gas is not always better, as high flow creates turbulence that draws air into the weld.

Why is my CO2 regulator icing up?

CO2 cools strongly as it expands, and at high flow or with long welds the regulator can freeze and stop the flow. Reduce the flow if you can, or fit a CO2 heater ahead of the regulator for continuous work.

How often should a regulator be replaced?

Have it checked at least once a year and replace it at the interval your gas supplier recommends, or sooner if it is damaged, leaks or the pressure creeps. Never repair a regulator yourself.

Can I order one with a welder?

Yes. The regulator is listed under related products on every welder page and can go on the same order. Trade customers can buy on account; see the delivery page for shipping options.