Manufacturer: Boltmark

Flat washer M12, form A

Boltmark M12 flat washer, form A, in bright zinc plated steel. It spreads the load under bolt heads and nuts, protects painted and soft surfaces and bridges slightly oversized holes. Made to ISO 7089 dimensions and packed in 200s, so there is always one to hand for every bolt.
SKU: BM-FWM12
In stock
Availability: In stock
Price
$0.50

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $0.48
50–199 $0.45
200+ $0.42

Sold in washers. Quantities round up to full packs.

Description

Overview

A flat washer is the simplest part of a bolted joint and one of the most useful. It gives the nut or bolt head a smooth, hard face to turn on, spreads the clamping force over a larger area and stops the fastener digging into the surface underneath.

These form A washers follow ISO 7089, the normal series for general engineering. They are punched from low carbon steel, deburred and zinc plated with a clear trivalent passivate for a bright, clean finish.

Sold in packs of 200 washers.

Where to use it

Fit a flat washer under the turning part of almost any bolted joint, and under both ends where the surface is soft or painted:

  • Steel brackets, frames and racking
  • Timber, plywood and composite panels
  • Painted, powder coated or galvanised parts
  • Slotted or slightly oversized holes
  • Threaded rod hangers and anchor fixings

Design and construction

Form A washers have a moderate outside diameter and thickness, roughly twice the bolt size across and about a quarter of the diameter thick. They are hard enough at around 200 HV to support grade 8.8 bolts in normal joints without dishing.

The bore is made slightly larger than the thread, so the washer slides easily over the bolt and sits flat against the head or nut. Both faces are flat and free of sharp burrs.

Because every washer in a pack is the same thickness, stacked joints stay square and bolt lengths work out as planned. That makes them a good choice for shimming small gaps in brackets and frames as well as for ordinary bolting. Many fitters also use them under coach screws and anchor nuts when fixing into timber or concrete.

Choosing the right size

Choose the washer by the thread size of the bolt or screw: an M10 bolt takes an M10 washer. The inside diameter, outside diameter and thickness of each size are listed in the technical specifications.

If you are fixing into soft timber or thin sheet and need more bearing area, a wider penny or form G washer is a better choice. For joints that vibrate, add a spring washer or use a nyloc nut; a flat washer alone does not lock.

Fitting and care

Place the washer directly under the part you turn, normally the nut. Where you add a spring washer, it goes between the flat washer and the nut. Make sure the washer sits square and is not trapped on a thread or weld bead before tightening.

Zinc plated washers are for indoor or covered use. Outdoors, near the sea or in wash-down areas, match the bolt and use stainless washers so the whole joint resists corrosion. Store packs in a dry place to keep the plating bright.

Packaging and ordering

Washers come in labelled packs of 200 with the size and barcode on the label, which makes restocking van boxes and stores bins quick. Most buyers order them with matching bolts and nuts; trade customers can add all three in one quick order and see tier pricing in the basket.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Thread size M12
Finish Zinc plated
Type Flat form A
Material Low carbon steel
Outside diameter (mm) 24
General
Brand Boltmark
Product type Flat washer, normal series
Application Bolted joints in steel, timber and painted parts
Country of manufacture Taiwan
Warranty 12 months against manufacturing defects
Performance
Neutral salt spray to white rust (h) 24 (ISO 9227)
Operating temperature (°C) -40 to +150
Dimensions and weight
Inside diameter (mm) 13
Thickness (mm) 2.5
Weight per 100 pieces (kg) 0.607
Packed weight (kg) 1.23
Materials and construction
Hardness (HV) 200 class (140 to 250)
Coating thickness (µm) 5 to 8
Passivation Clear trivalent, Cr(VI) free
Matching bolt grade Up to 8.8
Compliance and safety
Standards ISO 7089 (DIN 125-A), ISO 4042
CE / UKCA marked Not required for this product
RoHS compliant Yes
Packaging and ordering
Pack quantity 200 washers
Barcode type EAN-13 on pack label
Storage temperature (°C) 5 to 30, dry

FAQs

Which size washer do I need for my bolt?

Order the washer with the same thread size as the bolt, for example an M8 washer for an M8 bolt. The bore is made slightly larger than the thread so it slides on easily.

What is the difference between form A and form B?

Form A washers have a slightly larger outside diameter and are the normal choice for bolts. Form B washers are a little smaller across and are mostly used where space is tight. For general work form A is the safer pick.

Should the washer go under the bolt head or the nut?

Under whichever part you turn, normally the nut. On soft, painted or slotted parts fit one under both the head and the nut.

Will a flat washer stop my nut coming loose?

No, a flat washer only spreads the load. To resist vibration add a spring washer between the flat washer and the nut, or use a nyloc nut instead.

Can I use these washers with stainless bolts outdoors?

It is better not to. The zinc washer will corrode and stain the joint. Use stainless washers with stainless bolts so the whole fixing lasts.

Are washers sold individually?

Washers are sold in packs of 200. Trade customers can order several packs or sizes at once with quick order, and tier prices apply automatically in the basket.