Manufacturer: Edgecraft

Circular saw blade 165 mm, 48 teeth

Tungsten carbide tipped circular saw blade, 165 mm with 48 teeth, for softwood, hardwood, plywood and chipboard. The thin kerf eases the load on cordless saws, and the carbide teeth stay sharp far longer than steel blades.
SKU: EC-CB16548
In stock
Availability: In stock
Price
$12.00
RRP $15.00 Save 20%

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $11.40
50–199 $10.80
200+ $10.20

Description

Overview

The Edgecraft TCT blade fits handheld circular saws with a 165 mm blade. Each of its 48 teeth carries a brazed tungsten carbide tip, ground to an alternate top bevel for clean cuts across and along the grain.

The plate is laser cut and tensioned so it runs true at full speed. Expansion slots let it grow with heat without warping, and they cut down the ringing noise.

Where to use it

Use it for carpentry, first fix, shopfitting and general site cutting in timber-based materials.

  • Softwood studs, joists and battens
  • Hardwood boards and sills
  • Plywood, OSB and chipboard sheets
  • MDF and hardboard
  • Not for metal, masonry or fibre cement

Choosing teeth and diameter

Fewer teeth cut faster and clear chips well, which suits ripping and rough carpentry. The 24-tooth blades are the site choice for framing and fast cross-cuts. The 48-tooth blades leave a cleaner edge with less breakout on sheet materials and visible work.

Always fit the diameter your saw is made for. The 165 mm blades have a 20 mm bore. The 190 mm blades have a 30 mm bore and come with reducing rings for 20 mm and 16 mm arbors. Check that the saw's maximum speed does not exceed the speed marked on the blade.

Fitting and safe use

Disconnect the battery or plug before changing the blade. Fit it with the teeth and the arrow pointing in the saw's direction of rotation, and make sure the reducing ring sits flat. Check that the lower guard returns freely.

Let the blade reach full speed before cutting, support both sides of the work and avoid nails and screws. Wear eye and hearing protection and use dust extraction indoors, particularly on MDF.

Design and construction

The tungsten carbide tips are brazed into seats cut in the steel plate and ground after brazing, so each tooth cuts at the same height. Carbide stays sharp many times longer than steel teeth in abrasive materials such as chipboard and plywood glue lines.

The thin kerf removes less material in each cut. That puts less load on the motor, which means more cuts per charge on cordless saws and less strain on corded saws. A lower hook angle on the 48-tooth blades gives a calmer, more controlled cut in sheet materials.

The blade is marked with its diameter, bore, tooth count, direction of rotation and maximum speed. These markings are required under EN 847-1, the safety standard for woodworking tools, and let you check at a glance that the blade suits the saw before you fit it.

Care and ordering

Resin build-up makes a blade run hot and cut slowly. Clean it with a resin remover and a brush. Carbide teeth can be resharpened several times by a saw doctor. Trade buyers can keep both tooth counts on a saved list and reorder them with quick order.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Diameter (mm) 165
Type TCT
Teeth 48
Bore (mm) 20
General
Brand Edgecraft
Product type Circular saw blade
Application Softwood, hardwood, plywood, OSB, chipboard and MDF
Country of manufacture Italy
Warranty Against manufacturing defects
Performance
Tooth form Alternate top bevel (ATB)
Hook angle 10°
Maximum speed (rpm) 10000
Cut quality Fine finish
Suitable tools Handheld circular saws, corded and cordless
Dimensions and weight
Reducing rings (mm) None
Kerf width (mm) 2.2
Plate thickness (mm) 1.4
Net weight (kg) 0.29
Materials and construction
Tooth material Tungsten carbide, brazed
Plate material Hardened steel, laser cut and tensioned
Expansion slots Yes, laser cut
Compliance and safety
Standards EN 847-1
Recommended PPE Safety glasses, hearing protection, dust mask
Packaging and ordering
Pack quantity 1
Pack type Card sleeve with blade guard
Barcode type EAN-13
Storage temperature (°C) 5 to 40, dry

FAQs

Will a 190 mm blade fit my 165 mm saw?

No. Only fit the diameter your saw is designed for; a larger blade will not fit under the guard and is dangerous. Check the saw's rating plate or manual for the blade size and bore.

My saw has a 16 mm arbor. Which blade do I need?

The 190 mm blades come with reducing rings for 20 mm and 16 mm arbors. The 165 mm blades have a fixed 20 mm bore and suit saws with a 20 mm arbor.

Should I buy 24 or 48 teeth?

Choose 24 teeth for fast cuts in studs and joists where finish is not critical. Choose 48 teeth for a cleaner edge on sheet materials, laminated board and visible joinery.

Can I cut aluminium or laminate flooring with it?

It is not made for aluminium; use a blade with negative hook and triple-chip teeth for non-ferrous metal. Laminate flooring can be cut with the 48-tooth blade, though it will wear faster than in timber.

Can the blade be resharpened?

Yes. The carbide teeth can be reground several times by a saw sharpening service. Replace the blade if a tooth is missing or the plate is cracked or bent.

Why is my new blade burning the wood?

Burning usually comes from feeding too slowly, a pinched cut or resin on the blade. Support the work so the kerf stays open, keep a steady feed and clean the blade regularly.