Manufacturer: Peakguard

Rigger boot S3, tan

Tan rigger boot to EN ISO 20345 S3, with a steel toe cap, steel midsole and a pull-on design with no laces. Two pull loops make it quick to get on and off, and the oil-resistant rubber sole and water-resistant leather upper suit muddy sites, farms and yards.
SKU: PG-RB
Availability: Please select required attribute(s)
*
Price
$29.00

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $27.55
50–199 $26.10
200+ $24.65

Description

Product overview

The rigger boot is a tall, laceless safety boot first made for oil rigs and now common on building sites, farms and in civil engineering. With no laces there is nothing to come undone, catch on rebar or soak up mud, and the boot goes on in seconds.

This version has an oiled tan leather upper that resists water, a steel toe cap tested to 200 joules and a steel midsole against nails and sharp objects.

Where to use it

Rigger boots suit work on soft, wet and muddy ground, where the tall leg keeps out splashes and loose soil. Many groundworkers prefer them because they can be pulled off quickly at the cabin door.

The pull-on design gives less ankle support than a laced boot on rough, uneven ground or ladders. If you climb a lot, or need to adjust the fit through the day, a laced boot may be the better choice.

  • Groundworks and drainage
  • Concrete pours and civil engineering
  • Farms, stables and agricultural yards
  • Quarries and recycling sites
  • Marine and dockside work

Design and construction

The upper is oiled full-grain leather with a scuff-resistant toe cap cover and two strong pull loops. A soft fleece-style lining keeps the foot warm in winter, and the padded collar stops the top of the boot rubbing the shin.

The nitrile rubber outsole resists oil, fuel and heat up to 300 °C for short contact, and its deep self-cleaning cleats shed mud as you walk. A shock-absorbing heel and cushioned footbed reduce fatigue on hard ground.

Fit and sizing

Sizes run from UK 7 to 11. Because there are no laces, the fit around the ankle and instep matters: the heel should lift a little as you walk, but not slip out. Try them on with the thick socks you would wear on site.

If you are between sizes, choose the smaller one and add a thicker sock in winter. A rigger that is too large rubs the heel and wears quickly at the back.

Care and replacement

Hose or brush off mud at the end of the day and let the boots dry naturally, standing upright, away from heaters. Feed the leather with dubbin or wax every few weeks to keep it supple and water resistant.

Replace the boots if the toe cap has taken a heavy impact, the sole is worn smooth or splitting, or the upper is cracked. Concrete and lime dry out leather quickly, so clean them off promptly.

Keep a second pair in rotation if you work in wet conditions every day. Leather that dries fully between shifts lasts much longer, and a dry lining is warmer and kinder to your feet.

Ordering for gangs

Rigger boots are sold by the pair. Trade accounts see their tier prices, and the quick order form lets you add several sizes in one go when you kit out a gang. Save the order as a reorder list so new starters can be booted up quickly.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Type Rigger boot
Standard EN ISO 20345 S3
General
Brand Peakguard
Product type Rigger safety boot
Application Groundworks, civil engineering, agriculture, yards
Country of manufacture India
Sizes available UK 7 to 11
Warranty 6 months against manufacturing defects
Performance
Toe cap impact (J) 200
Toe cap compression (kN) 15
Penetration resistance Steel midsole (P)
Slip resistance SRC
Additional markings HRO (heat-resistant outsole to 300 °C), FO
Dimensions and weight
Net weight (kg) 2.10 per pair, size 9
Shaft height (mm) 270
Width fitting G (wide)
Materials and construction
Upper material Oiled full-grain leather, tan
Toe cap material Steel
Outsole Nitrile rubber, deep cleat
Lining Warm fleece-style lining
Footbed Removable, antistatic, cushioned
Fastening Pull-on, two pull loops
Compliance and safety
Standards EN ISO 20345:2011
PPE category Category II
CE / UKCA marked Yes
Antistatic Yes (A)
Packaging and ordering
Pack quantity 1 pair
Barcode type EAN-13

Documents

FAQs

Are rigger boots waterproof?

The oiled leather upper is water resistant and copes with wet, muddy ground. They are not designed for standing in water above the sole for long periods; for that, a safety wellington is better.

Do rigger boots give enough ankle support?

They give less ankle support than a laced boot because the fit cannot be tightened. On rough ground, scaffolding or ladders, a laced S3 boot is usually the safer choice.

How should rigger boots fit?

Snug around the instep, with the heel lifting a little as you walk but not slipping out. Try them with the socks you wear on site, and choose the smaller size if you are between two.

Are they lined for winter?

Yes, a warm fleece-style lining keeps feet warmer in cold weather. In hot weather they can feel warm, so some wearers switch to a laced boot in summer.

How do I look after the leather?

Clean off mud, concrete and lime at the end of the day, let the boots dry naturally and treat the leather with dubbin or wax every few weeks. This keeps the leather supple and stops it cracking.

Do you sell them in half sizes?

They come in whole UK sizes from 7 to 11. If you are a half size, most wearers go down to the nearest whole size and wear a slightly thicker sock.