Manufacturer: Boltmark

Nyloc nut M12, zinc plated

Boltmark M12 nyloc nut with a nylon locking ring that grips the bolt thread and resists loosening under vibration. Grade 8 steel with a bright zinc finish, it suits machinery, trailers and anything that shakes. Packs of 100 for workshop and van stock.
SKU: BM-NNM12
In stock
Availability: In stock
Price
$0.50

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $0.48
50–199 $0.45
200+ $0.42

Sold in nuts. Quantities round up to full packs.

Description

Overview

A nyloc nut is a hexagon nut with a nylon ring set into its top. When the bolt thread reaches the ring it cuts its own thread into the nylon, which presses back on the bolt and creates friction. That friction holds the nut in place even if the joint loses some clamping force, so the nut does not spin off under vibration. It also means the nut holds its position on joints that are deliberately left slightly slack.

These Boltmark nuts are made to property class 8 and match grade 8.8 bolts. They are zinc plated with a clear trivalent passivate for indoor and sheltered use. Because the lock is part of the nut, there is no loose washer to forget or drop into a machine during a repair.

Sold in packs of 100 nuts.

Where to use it

Fit nyloc nuts wherever movement or vibration could loosen a plain nut:

  • Pumps, fans, compressors and motor mounts
  • Trailers, tow bars and agricultural equipment
  • Conveyor frames and machine guards
  • Pivot points that must not be fully clamped
  • Generator and compressor frames and wheel kits

Design and construction

The steel body is cold forged and tapped with a metric coarse thread. A white polyamide insert is crimped into a collar on top of the nut. The locking effect works without any extra parts, so it saves a lock washer and stays effective at any tightness, including on pivots where the nut is set to a clearance.

Nylon softens at high temperature. The insert is rated to about 120 °C, so do not use these nuts on exhaust parts, engine manifolds or ovens.

Choosing and fitting

Match the thread size to the bolt; all sizes are metric coarse. Use a bolt long enough for at least two full threads to pass through the nylon ring, otherwise the lock does not engage properly.

Start the nut by hand, then use a spanner or socket once the bolt reaches the insert. The nut will feel stiff from that point; this is the locking torque, not a cross thread. Tighten to the torque the bolt grade calls for. A power tool is fine for running on, but finish with a torque wrench on critical joints.

Reuse and care

The nylon loses some grip each time the nut is removed. On safety-related joints, such as wheels, brakes or lifting gear, always fit a new nut. On general equipment a nut can be reused a few times as long as it still needs a spanner to turn once on the thread.

Store nuts out of direct sunlight; long UV exposure makes nylon brittle.

Packaging and ordering

Supplied in labelled packs of 100 with a barcode for quick booking in. Many workshops keep a stock of each size next to the plain nuts so fitters always replace a nyloc with a nyloc. Trade buyers can combine sizes in one quick order, and tier prices apply in the basket when you are signed in.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Thread size M12
Material Steel grade 8
Type Nyloc nut
Finish Bright zinc plated, clear trivalent passivate
General
Brand Boltmark
Product type Prevailing torque hexagon nut with nylon insert
Application Joints exposed to vibration, indoors or under cover
Country of manufacture Taiwan
Warranty 12 months against manufacturing defects
Performance
Proof load stress (MPa) 800 minimum
Operating temperature (°C) -40 to +120
Reuse Limited; replace on safety-related joints
Minimum thread protrusion 2 full threads beyond the insert
Dimensions and weight
Thread pitch (mm) 1.75
Width across flats (mm) 18
Nut height (mm) 14
Weight per 100 pieces (kg) 1.5
Packed weight (kg) 1.52
Materials and construction
Insert material Polyamide 6.6, white
Thread type Metric coarse, tolerance 6H
Matching bolt grade Up to 8.8
Compliance and safety
Standards ISO 7040, ISO 2320, ISO 898-2
CE / UKCA marked Not required for this product
RoHS compliant Yes
Packaging and ordering
Pack quantity 100 nuts
Barcode type EAN-13 on pack label
Storage temperature (°C) 5 to 30, away from direct sunlight

FAQs

Can I reuse a nyloc nut?

On general equipment you can reuse one a few times, as long as it still needs a spanner to turn once the bolt reaches the nylon. On wheels, brakes, steering or lifting gear always fit a new nut.

Do I still need a spring washer with a nyloc nut?

No. The nylon insert does the locking. A flat washer under the nut is still a good idea on soft or painted surfaces to spread the load.

How hot can a nyloc nut get?

The nylon insert is good to about 120 °C. Above that it softens and loses its grip, so on exhausts, engines and ovens use an all-metal lock nut instead.

The nut is hard to turn halfway on. Is it cross-threaded?

Probably not. Once the bolt reaches the nylon ring the nut needs a spanner to turn; that resistance is how it locks. If it is hard to start in the first few turns, back it off and check the thread.

How long should the bolt be?

Long enough that at least two full threads pass right through the nylon ring after tightening. A bolt that stops inside the insert gives a weak lock.

Are these nuts suitable for outdoor use?

The zinc finish is for indoor or sheltered use. Outdoors it will corrode over time; in wet or coastal areas use stainless fixings instead.