Manufacturer: Lumenford

LED batten 4 ft, 20 W

Lumenford 4 ft LED batten, 20 W at 4000 K, that replaces single fluorescent tube fittings in one simple swap. Slim, light and quick to wire, with an opal diffuser for even light in stores, garages, plant rooms, stairwells and back-of-house areas.
SKU: LF-BT4FT
In stock
Availability: In stock
Price
$13.50

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $12.82
50–199 $12.15
200+ $11.48

Description

Overview

An LED batten is the simplest way to replace an old fluorescent fitting. The LEDs and driver are built in, so there are no tubes, starters or chokes to fail, and the fitting lights instantly at full output with no flicker. It uses roughly half the energy of the fluorescent fitting it replaces.

The batten is slim and light, with an opal diffuser that hides the individual LEDs and spreads the light evenly. It fixes directly to the ceiling or wall, and the terminal block is reached by removing the diffuser.

Where to use it

Battens suit any indoor area where practical, even light is more important than appearance.

  • Stockrooms, garages and workshops
  • Plant rooms and service corridors
  • Stairwells and car park lobbies
  • Back-of-house areas in shops and restaurants
  • Replacing 4, 5 and 6 ft fluorescent fittings

Choosing the right length

Match the length to the fitting you are replacing, so the existing cable position and fixings can be reused. The 4 ft batten gives around 2400 lumens, the 5 ft around 3000 lumens and the 6 ft around 3600 lumens. That is about the same light as a fluorescent fitting of the same length, from much less power.

For a new installation, longer battens give more light per fixing point. Space them evenly along the room for uniform light on the floor or the work surface.

Design and construction

The body is a galvanised steel base with a polycarbonate opal diffuser that clips on along its length. Polycarbonate does not shatter, which matters in stores and garages where the fitting may be knocked. The LED board is mounted on an aluminium strip that carries heat away from the LEDs and keeps them running cool for a long life.

The batten has cable entry holes at the back and both ends, and a terminal block that accepts up to 2.5 mm² conductors.

Installation and care

Isolate the circuit, remove the old fitting and fix the batten with screws suited to the surface. Connect line, neutral and earth to the terminal block, clip the diffuser back on and restore the supply. The batten is Class I and must be earthed.

Wipe the diffuser with a damp cloth when it gets dusty. There are no lamps to replace, so maintenance is limited to periodic cleaning and inspection.

  • Suitable for ceiling or wall mounting
  • Not for damp or outdoor locations: IP20
  • Not compatible with dimmers

Compliance and ordering

The batten is made to EN 60598-1 and EN 60598-2-1 for fixed general-purpose luminaires and is CE and UKCA marked. It contains no mercury, so there are no special disposal rules for old tubes once the fluorescent fittings have gone, although the old fittings must still be recycled as electrical waste.

Each batten is packed in a long carton with fixing points marked on a template. Facilities teams replacing fittings across a site can order all three lengths together and save the list for later phases of the work.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Size 4 ft
Power (W) 20
Colour temperature 4000 K
IP rating IP20
General
Brand Lumenford
Product type LED batten, integrated
Application Indoor utility and back-of-house lighting
Country of manufacture China
Warranty 3 years
Performance
Luminous flux (lm) 2400
Efficacy (lm/W) 120
Colour rendering (CRI) > 80
Beam angle (°) 120
Rated life (hours, L70) 40,000
Operating temperature (°C) -20 to +40
Electrical
Input voltage (V) 220 to 240 AC, 50/60 Hz
Power factor > 0.9
Driver Integrated, flicker-free
Dimmable No
Protection class Class I
Terminal capacity Up to 2.5 mm²
Dimensions and weight
Dimensions (L × W × H, mm) 1220 × 70 × 35
Net weight (kg) 0.6
Packed weight (kg) 0.8
Materials and construction
Body Galvanised steel base
Diffuser Polycarbonate, opal
Compliance and safety
Energy class E
Standards EN 60598-1, EN 60598-2-1
CE / UKCA marked Yes
RoHS compliant Yes
Packaging and ordering
Pack quantity 1
Barcode type EAN-13

Documents

FAQs

Can I replace a fluorescent fitting with this batten directly?

Yes. Remove the old fitting and wire the batten to the same supply. Choose the same length so the existing fixing points and cable position line up.

Can I install it in a bathroom or outdoors?

No. The batten is rated IP20 and is for dry indoor locations only. For damp areas, car parks or outdoor use, choose an IP65 non-corrosive fitting.

Can the batten be dimmed?

No, the integrated driver is not dimmable. Connect it to a standard switch only.

Is the batten suitable for a cold garage or store?

Yes. It works from -20 °C and starts instantly at full brightness, unlike fluorescent tubes, which are slow and dim in the cold.

Does it need an earth connection?

Yes. The batten is Class I with a steel base, so the earth conductor must be connected to the earth terminal.

Can I buy them in bulk for a full refit?

Yes. Add the quantity you need or use the quote basket for a project, and tier prices apply automatically to trade accounts. Mix lengths in one order to match the existing fittings.