Manufacturer: Torqline

Combination spanner 10 mm

Torqline 10 mm combination spanner in drop-forged chrome vanadium steel, with an open end and a 12-point offset ring. The ring grips the flats rather than the corners, so it turns tight nuts and bolts without rounding them.
SKU: TQ-CS10
In stock
Availability: In stock
Price
$4.40

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $4.18
50–199 $3.96
200+ $3.74

Description

Overview

The Torqline combination spanner has an open jaw at one end and a 12-point ring at the other, both 10 mm. Use the ring to break a fastener loose or to apply final torque, and the open end to spin it quickly where the ring cannot reach.

It is drop-forged from chrome vanadium steel, hardened and tempered, then finished in satin chrome that resists rust and wipes clean.

Where to use it

It is the standard spanner for maintenance teams, fitters, electricians and installers.

  • Metric hex bolts and nuts on frames and brackets
  • Machine guards, motor mounts and pump bases
  • Cable glands and conduit fittings
  • Racking, shelving and strut channel
  • Generator and compressor servicing

Design and construction

The ring end uses a flank drive profile. It loads the flats of the hex instead of the corners, which reduces slipping on worn or painted fasteners. The ring is offset by 15° to clear the hand from the work surface.

The open jaw is angled at 15° to the handle, so flipping the spanner gives a new working position in tight spaces. Dimensions and strength follow DIN 3113 and ISO 7738. The size is stamped on both sides of the handle.

Choosing the size

Choose by the size across the flats of the hex, not the thread. For ISO 4017 hex bolts the usual pairs are: M5 uses 8 mm, M6 uses 10 mm, M8 uses 13 mm, M10 uses 17 mm and M12 uses 19 mm.

Many fitters carry 10, 13, 17 and 19 mm as their core sizes. Each size is sold separately, so you can replace a lost spanner without buying a whole set.

Spanner or socket

A combination spanner is quick and reaches where a ratchet will not fit, but it gives less control over torque. For final tightening of structural bolts, flanges and wheel nuts, use a torque wrench with a socket set to the value in the drawing or manual.

For repetitive work on long threaded rods or many fasteners, an air or cordless impact wrench saves time. Use the spanner to hold the nut on the other side, or to finish and check by hand.

On nyloc nuts, expect resistance all the way down; that is the locking insert doing its job, not a cross-thread. On zinc-plated or stainless fasteners that have been outdoors, a little penetrating oil before turning makes the job easier and protects the threads from galling. The 10 mm spanner is also handy for holding a bolt head while a nut is tightened with a socket.

Safe use and care

Pull rather than push, so your knuckles stay clear if the fastener breaks loose. Never extend the handle with a tube or strike it with a hammer, as that overloads the jaw. Use a torque wrench when a specified torque is required.

Wipe off oil and grit after use and store the spanner dry. Replace it if the jaw has spread or the ring is cracked.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Size 10
Material Chrome vanadium steel, drop-forged
Finish Satin chrome
General
Brand Torqline
Product type Combination spanner
Application Metric hex nuts and bolts
Country of manufacture Taiwan
Warranty Lifetime, against manufacturing defects
Performance
Ring profile 12-point flank drive
Ring offset 15°
Open jaw angle 15°
Matching thread (ISO 4017) M6
Dimensions and weight
Overall length (mm) 145
Ring head thickness (mm) 7.5
Net weight (kg) 0.06
Packed weight (kg) 0.07
Materials and construction
Heat treatment Hardened and tempered
Size marking Stamped on both sides of the handle
Compliance and safety
Standards DIN 3113 form A, ISO 7738
Insulated No; not for live electrical work
Packaging and ordering
Pack quantity 1
Pack type Hanging card
Barcode type EAN-13
Storage temperature (°C) -20 to 50, dry

FAQs

Which spanner fits an M10 bolt?

A standard M10 hex bolt or nut to ISO 4017 or ISO 4032 takes a 17 mm spanner. Some older DIN fasteners and flange nuts differ, so measure across the flats if in doubt.

Will a 12-point ring round off nuts?

The flank drive ring grips the flats, not the corners, so it is less likely to round a fastener than older 12-point designs. For badly corroded nuts, a 6-point socket gives the most grip.

Can I use it on imperial fasteners?

These are metric sizes. A few happen to fit imperial sizes closely, but a loose fit can slip and damage the fastener, so use AF spanners for imperial work.

Is the spanner insulated for electrical work?

No. It is bare chrome vanadium steel and must not be used on or near live parts. Use VDE insulated tools tested to 1000 V for live working.

What does the lifetime warranty cover?

It covers defects in materials and manufacture for the life of the tool. It does not cover misuse such as hammering the handle, adding extension tubes or normal wear.

Do you sell these as a set?

Each size is sold on its own so you can build the set you need. Add several sizes to your cart at once using quick order with the SKUs.