Manufacturer: Boltmark

Spring washer M10

Boltmark M10 spring washer with a square section, made from hardened spring steel and zinc plated. It adds spring tension under a nut or bolt head to help keep joints tight under light vibration. Packed in 200s for workshops, maintenance stores and van stock.
SKU: BM-SWM10
In stock
Availability: In stock
Price
$0.50

PRICE BREAKS - The more you buy, the more you save

Quantity Unit price
10–49 $0.48
50–199 $0.45
200+ $0.42

Sold in washers. Quantities round up to full packs.

Description

Overview

A spring washer is a split ring of hardened steel with its ends set slightly apart. As the nut is tightened, the washer is pressed flat and pushes back, keeping a little tension in the joint. The sharp ends also bite into the nut and the surface below, which helps resist the nut turning back.

These washers have a square section to the DIN 127 B pattern, the shape most UK workshops know. They are hardened, zinc plated and baked to reduce the risk of hydrogen embrittlement.

Sold in packs of 200 washers.

Where to use it

Spring washers are a simple, low-cost way to help hold joints that see light, steady vibration:

  • Electrical enclosures, cable tray and trunking
  • Panel fixings, covers and guards
  • Light machinery, fans and ducting
  • Fixtures, jigs and workshop equipment
  • Replacing like for like on existing equipment

Design and construction

Each washer is coiled from square spring steel wire, cut and set so the ends stand proud. Heat treatment brings it to between 420 and 510 HV, hard enough to spring back rather than flatten permanently. The zinc plate with clear passivate protects it indoors and keeps it easy to see in a parts tray.

The section size grows with the thread, so larger washers give more spring force and bigger bearing faces.

Each washer is checked for set and hardness at the factory. A correctly made spring washer springs back to its original gap after being pressed lightly in a vice; one that stays flat has lost its temper and should be scrapped.

Choosing and fitting

Choose the washer by the thread size of the bolt. Fit it directly under the nut, or under the bolt head if the head is the part you turn. If the surface is soft or painted, put a flat washer underneath first so the spring washer bears on steel.

Tighten until the washer is pressed flat. A spring washer that is still visibly split after tightening means the joint is not tight enough. Fit a new washer whenever the joint is taken apart, because a used washer loses some of its spring.

Limits to know

Spring washers work well on lower and medium strength joints. On high-strength bolts tightened to full torque, the washer is flattened completely and adds little extra locking. Where vibration is strong, such as engines, compressors and vehicle running gear, use nyloc nuts or another approved locking method instead.

Do not use spring washers on soft materials such as aluminium or plastic without a flat washer underneath; the ends can cut into the surface. The same applies to joints that must stay sealed or that carry an electrical bond, where the split ends can damage a gasket or a plated contact face.

Packaging and ordering

Supplied in labelled packs of 200 with a barcode for scanning into stores. Order them alongside nuts, bolts and flat washers in one quick order; trade customers see their tier prices in the basket.

Demo product: invented for the Cartenvo B2B demo store.

Technical specifications

Specifications

Products specifications

Attribute name Attribute value
Thread size M10
Finish Zinc plated
Type Spring
Material Hardened spring steel
Outside diameter (mm) 18.1
General
Brand Boltmark
Product type Split spring lock washer, square section
Application Bolted joints with light vibration, indoors
Country of manufacture Taiwan
Warranty 12 months against manufacturing defects
Performance
Operating temperature (°C) -40 to +150
Reuse Not recommended; fit a new washer
Dimensions and weight
Inside diameter (mm) 10.2
Section, width × thickness (mm) 3.5 × 2.2
Weight per 100 pieces (kg) 0.3
Packed weight (kg) 0.62
Materials and construction
Hardness (HV) 420 to 510
Coating thickness (µm) 5 to 8
Passivation Clear trivalent, Cr(VI) free
Hydrogen embrittlement relief Baked after plating
Matching bolt grade Up to 8.8
Compliance and safety
Standards DIN 127 B pattern, ISO 4042
CE / UKCA marked Not required for this product
RoHS compliant Yes
Packaging and ordering
Pack quantity 200 washers
Barcode type EAN-13 on pack label
Storage temperature (°C) 5 to 30, dry

FAQs

Where does a spring washer go?

Directly under the part you turn, normally the nut. If the surface is soft or painted, fit a flat washer first and the spring washer on top of it, then the nut.

How do I know it is tight enough?

Tighten until the washer is pressed completely flat. If you can still see a gap at the split, the joint is not tight.

Can I reuse spring washers?

It is best not to. Once flattened, a washer loses some of its spring and grip, so fit a new one each time the joint is taken apart. They are low-cost and sold in packs of 200 for this reason.

Are spring washers enough for heavy vibration?

Not on their own. On high-strength bolts at full torque or on engines, compressors and vehicle parts, use nyloc nuts or another approved locking method.

Can I use them on aluminium?

Only with a flat washer underneath. The sharp ends of the spring washer can dig into soft metals and plastics and damage the surface.

Do you sell stainless spring washers?

This range is zinc plated spring steel for indoor use. For outdoor or wash-down areas, ask our sales team about stainless options before ordering.